Desert Dawn Granny Square Wrap Free Crochet Pattern

Introduction

The Desert Dawn Granny Square Wrap is a small project with a big personality: a boho-cozy sleeve for your dish soap bottle, crocheted in warm spice tones of ochre, clay, and deep red. It's designed for beginners who have just learned the granny square and want a quick, satisfying project that uses up leftover cotton. Four little squares join into a diamond band that slips right over the bottle, finished with scalloped edges at the top and bottom. It looks like a sunset in your sink caddy and feels like a sturdy, slightly textured cotton fabric that wipes clean and holds its shape.

Materials Needed

• Yarn: Worsted weight (4) cotton yarn, approximately 50 yards total: 20 yards ochre (A), 15 yards clay (B), 15 yards deep red (C)
• Hook: 4 mm (G-6)
• Notions: Tapestry needle, scissors, stitch marker (optional)
• Finished size: Fits a standard dish soap bottle 2.5–3 inches (6.5–7.5 cm) in diameter; wrap measures about 6 inches (15 cm) tall and 9 inches (23 cm) in circumference when flat

Abbreviations

• ch – chain
• sl st – slip stitch
• sc – single crochet
• dc – double crochet
• sp – space
• st(s) – stitch(es)
• sk – skip
• rep – repeat

Gauge

The first 3 rounds of the granny square should measure 2.5 inches (6.5 cm) square. Work one square through Round 3 and measure it flat; if it's larger, go down a hook size, and if it's smaller, go up.

Tips Before You Start

• Keep your ch-1 spaces snug. Loose chain spaces make the wrap baggy around the bottle, so pull each chain gently after making it.
• Work all four squares before joining so your tension stays consistent from square to square.
• When joining, work from the wrong side so the seams sit flat against the bottle and the right side stays smooth.
• Try the tube on the bottle before adding the edgings; it should slip on with a little ease, not stretch tight.

Step-by-Step Instructions

Granny Square (make 4)

R1: With A, ch 4, join with sl st to form ring. Ch 3 (counts as dc), 2 dc in ring, [ch 2, 3 dc in ring] 3 times, ch 2, join with sl st to top of ch-3. (12 dc, 4 ch-2 sps)

R2: Ch 3, 2 dc in same sp, ch 2, 3 dc in same sp (corner made), *ch 1, [3 dc, ch 2, 3 dc] in next ch-2 sp; rep from * 2 more times, ch 1, join with sl st to top of ch-3. (24 dc, 4 ch-1 sps, 4 ch-2 sps)

R3: Ch 3, 2 dc in same sp, ch 2, 3 dc in same sp, *ch 1, 3 dc in next ch-1 sp, ch 1, [3 dc, ch 2, 3 dc] in next ch-2 sp; rep from * 2 more times, ch 1, 3 dc in next ch-1 sp, ch 1, join with sl st to top of ch-3. Fasten off A. (36 dc, 8 ch-1 sps, 4 ch-2 sps)

R4: Join B with sl st in any ch-2 sp, ch 3, 2 dc in same sp, ch 2, 3 dc in same sp, *[ch 1, 3 dc in next ch-1 sp] twice, ch 1, [3 dc, ch 2, 3 dc] in next ch-2 sp; rep from * 2 more times, [ch 1, 3 dc in next ch-1 sp] twice, ch 1, join with sl st to top of ch-3. Fasten off B. (48 dc, 12 ch-1 sps, 4 ch-2 sps)

R5: Join C with sl st in any ch-2 sp, ch 3, 2 dc in same sp, ch 2, 3 dc in same sp, *[ch 1, 3 dc in next ch-1 sp] 3 times, ch 1, [3 dc, ch 2, 3 dc] in next ch-2 sp; rep from * 2 more times, [ch 1, 3 dc in next ch-1 sp] 3 times, ch 1, join with sl st to top of ch-3. Fasten off C. (60 dc, 16 ch-1 sps, 4 ch-2 sps)

Square measures about 4 inches (10 cm).

Assembly

Arrange the four squares in a row, each rotated 45 degrees so they form a diamond band, with corners touching. Join squares with sl st in C through corresponding ch-1 sps and corner ch-2 sps, working from the wrong side to create flat seams. Join the first and last squares to form a tube, leaving a 1-inch opening at the top for the bottle neck. Weave in ends.

Top Edging

Rnd 1: Join C at top edge, ch 1, sc evenly around top opening (about 24 sc).

Rnd 2: Ch 1, *sc in next st, sk 1 st, 5 dc in next st, sk 1 st, sc in next st; rep from * around, join with sl st to first sc. Fasten off.

Bottom Edging

Rnd 1: Join C at bottom edge, ch 1, sc evenly around bottom (about 36 sc).

Rnd 2: Ch 1, *sc in next st, sk 1 st, 5 dc in next st, sk 1 st, sc in next st; rep from * around, join with sl st to first sc. Fasten off. Weave in ends.

Assembly and Finishing

Seam the squares as described above, then close the band into a tube, leaving the 1-inch top opening for the bottle neck. Weave in all ends on the wrong side, threading each tail through a few stitches before trimming. Block lightly by misting the wrap with water and shaping it over the bottle (or a similar-sized jar) so the seams lie flat and the scallops sit evenly; let it dry completely before removing.

Pro Tips and Variations

• Swap the spice palette for cool tones like sage, teal, and cream for a different kitchen mood.
• Make a taller version by joining six squares instead of four for a larger bottle or a utensil holder.
• Work the scallop round in the same color as the last square round for a subtle, tone-on-tone edge.